BT20F, BT20BF, BT20NE nRF54LM20A, nRF54LM20B BLE 6.0 Thread, Zigbee Modules
nRF54LM20A and nRF54LM20B BLE 6.0 Modules
BT20F Series modules use Nordic nRF54LM20A or nRF54LM20B BLE 6.0 SoC with a Cortex M33 MCU at 128 MHz, 2036 KB flash, 512 KB RAM. No external component is required.
nRF54LM20B has an embedded Axon NPU, an inference engine to process sensor data at the edge. It can reduce power consumption for transmitting data to the cloud and reduce the impact of unreliable cloud connection.
BT20NE integrates an nRF21540 power amplifier. Idle current is high. BM20XE with a Skyworks SKY66403 power amplifier is recommended for battery-powered products requiring high transmission power.
BT20F integrates the inverted F antenna which performs much better than all chip antennas we have tested. The integrated F antenna of BT20NE performs better than the chip antenna of BM20XE.
BT20F is not footprint compatible with BT840F or BT40F series modules.
When used as a basic UART communication device, you don’t need to use the LGA pins. A UART port, the SWDIO port, and a few GPIOs use the castellated pins.
Module Summaries
BT20F, BT20BF
Size 15.0x20.8x2mm
BT20F, an nRF54LM20A module with an integrated high performance PCB antenna.
BT20BF, an nRF54LM20B module with an integrated high performance PCB antenna. An Axon NPU for Edge AI applications.
BT20NE
Size 15.0 x28.0 x2mm
BT20NE, an nRF54LM20A module with an nRF21540 power amplifier.
An integrated high performance PCB antenna and an u.FL connector for external antenna.
BT20BNE
Size 15.0 x28.0 x2mm
BT20BNE, an nRF54LM20B module with an nRF21540 power amplifier.
An integrated high performance PCB antenna and an u.FL connector for external antenna.
An Axon NPU for Edge AI applications.
BT20F Series Specifications
BLE 6.0, IEEE 802.15.4-2006 Transceiver
Complete RF solution with integrated antenna
BLE: 2Mbps, 1Mbps (-96 dBm sensitivity), 500kbps, 125kbps (-106 dBm sensitivity).
IEEE 802.15.4-2006: 250 kbps (-102 dBm sensitivity).
Proprietary: 4Mbps, 2Mbps, 1Mbps.
Programmable TX power, -8 dBm +8 dBm.
Channel sounding for Bluetooth range measurements.
128 bit AES/ECB/CCM/AAR co-processor (on-the-fly operation).
12.0 mW TX current at 0 dBm, 1Mbps, 1.8V VDD.
7.5 mW RX current, 1Mbps, 1.8V VDD.
Both 32.0 MHz and 32.768 kHz crystals embedded.
RSSI, 1 dB resolution
Platform Security
Secure/non-secure memory protection.
Symmetric and asymmetric key crypto accelerator.
Secure key management.
Tamper detection.
Immutable boot partition.
Debug access port protection.
Two watchdog timers for secure and non-secure context.
MCU
Nordic nRF54L with ARM Cortex M33, 128 MHz.
Flash/RAM: 2036KB/512KB.
505 EEMAC CoreMark score running from non-volatile memory, 3.95 CoreMark per MHz.
Single precision floating point unit (FPU).
Memory protection unit (MPU).
Digital signal processing (DSP) instructions.
Data watchpoint and trace (DWT), embedded trace macrocell (ETM), instrumentation trace macrocell (ITM), and cross trigger interface (CTI).
Serial Wire Debug (SWD)
Trace port interface unit (TPIU), 4-bit parallel trace of ITM and ETM trace data; Serial wire output (SWO) trace of ITM data.
Peripherals
Two realtime counters (RTC), and one global RTC (GRTC) that can run in System OFF mode and implement a shared system timer.
Seven 32-bit timers with counter mode.
Five fully featured serial interfaces with EasyDMA, supporting I2C, SPI controller/peripheral, and UART.
Three pulse width modulator (PWM) units with Easy DMA.
I2S two channel inter-IC sound interface.
14-bit at 20KS/s, 12 bit at 250KS/s, or 10-bit at 2MS/s ADC with up to eight programmable gain channels.
Near field communication (NFC).
Two quadrature decoders (QDEC).
90 LGA pins, 66 GPIOs.
Embedded inductors for DCDC converter
1.7V to 3.6V supply voltage with up to 3.6V I/O voltage.
Operation temperature: -40°C to +85°C.
Certifications
FCC ID:
ISED ID:
Europe:
Australia and New Zealand:
Japan TELEC:
Taiwan NCC:
QDID:
Availability: Production
DOWNLOAD document
Order Products
For volume discount and production lead time, please email Fanstel.
